DWDM-SFP10G-31.12-I represents a 10GBASE-DWDM SFP+ optical transceiver tuned to 1531.12nm (ITU C58) with throughput capability up to 10.7Gbps, qualified across an industrial case temperature range of -40°C to +85°C. The cooled EML laser and APD photodiode combination preserves signal fidelity over 80km SMF links, supported by real-time digital diagnostic monitoring (DDM) for ongoing performance visibility.
ใช้งานร่วมกับ Netgear DWDM-SFP10G-31.12-I ได้ LINK-PP brings 10G DWDM capacity to industrial fiber backbones with 80km reach and a ruggedized hardware build. Combining a 1531.12nm wavelength, duplex LC connectivity, and built-in diagnostics, it lets operators expand 10G capacity on existing single-mode routes while keeping links dependable in uncontrolled industrial environments.
This DWDM SFP+ transceiver follows the SFP+ Multi-Source Agreement, so it fits a wide range of switches and transport platforms without modification. Its hot-swappable design lets technicians replace or add units while the network stays online.
DWDM-SFP10G-31.12-I: 10 Gbps Connectivity for Industrial Fiber Backbones
Line rates of up to 10.7Gbps let this DWDM module move large traffic volumes with very low latency. That steady 10G capacity suits industrial fiber backbones, where long-term headroom matters more than raw port count.
Dense wavelength division multiplexing lets several 10G DWDM channels travel over one fiber pair at the same time. Adding capacity this way avoids the cost and delay of pulling new cable through a plant.
The transmitter inside this optical transceiver is locked to 1531.12nm, the ITU C58 channel on a 100GHz spacing plan. Holding that exact frequency keeps neighboring channels cleanly separated during multiplexing.
A sensitive APD receiver allows the module to carry signals up to 80km of single-mode fiber without regeneration. That reach removes the need for powered repeater sites along the route.
Standard duplex LC ports accept common single-mode patch cords and keep insertion loss low at every mating. The compact connector body also leaves room for tidy cabling in crowded racks.
Digital diagnostic monitoring (DDM) reports transmit power, receive power, bias current, supply voltage, and operating temperature directly from the module. Engineers can read those values remotely to spot a degrading link before traffic drops.
ใช้งานร่วมกับ Netgear DWDM-SFP10G-31.12-I ได้ LINK-PP 10G SFP+ DWDM transceiver is built and verified against recognized international standards, holding ISO 9001 for quality management alongside CE, RoHS, and FCC compliance so that it can be shipped and deployed in markets worldwide.
Before any DWDM module leaves the line, it passes a structured sequence of optical and electrical checks-spectral verification, eye diagram review, and bit error rate runs-that confirms each module behaves as specified under real traffic.
ใบรับรองคุณภาพ DWDM-SFP10G-31.12-I
The module's international approvals show that it was built to recognized manufacturing and environmental requirements, which gives network operators a documented basis for trusting its long-term reliability.
This SFP+ DWDM transceiver is pre-programmed to match the identification data that major switch and router platforms expect, so it initializes normally and keeps a stable link without compatibility warnings.
ใช้งานร่วมกับ Netgear DWDM-SFP10G-31.12-I ได้ LINK-PP DWDM SFP+ transceiver undergoes strict testing to ensure stable performance in industrial environments. Learn more about our testing process at the LINK-PP ศูนย์สนับสนุนการทดสอบ
การทดสอบสเปกตรัมแสง
Verify wavelength accuracy and spectral stability for reliable DWDM transmission.
การทดสอบรูปแบบตา
Check signal clarity and quality for stable optical data transmission.
การทดสอบอัตราข้อผิดพลาดบิต
Measure data accuracy to ensure reliable long-distance optical signal transmission.
ทดสอบอุณหภูมิ
Verify stable module performance under industrial operating temperature conditions.
อุปกรณ์ Netgear DWDM-SFP10G-31.12-I ทุกรุ่นที่ใช้งานร่วมกันได้ LINK-PP 10G DWDM SFP+ module is packed to protect both its optical ports and its internal electronics from handling and transit hazards. Orders are processed promptly and shipped through established international channels to reach customers reliably.
บรรจุภัณฑ์ป้องกันไฟฟ้าสถิต
Wrap each module against electrostatic discharge with anti-static packaging.
ระบบป้องกันการขนส่งที่ทนทานต่อแรงกระแทก
Cushion each carton against impact and vibration during transit.
ดำเนินการและจัดส่งคำสั่งซื้ออย่างรวดเร็ว
Handle confirmed orders promptly and release stock for immediate dispatch.
โลจิสติกส์ระดับโลกและการจัดส่งระหว่างประเทศ
Ship worldwide through established carriers with reliable, trackable delivery.
Deploy the DWDM-SFP10G-31.12-I DWDM SFP+ by inserting the module into switch slots and connecting LC fiber cables directly to a matching-wavelength DWDM Mux/Demux. It builds high-density, long-haul industrial fiber backbones capable of stable 10G data transport across harsh environments.
Yes, DDM/DOM provides real-time telemetry for received optical power (Rx power), Tx power, and module temperature directly via your switch CLI or NMS. If Rx power drops near the sensitivity threshold, inspect the fiber route, connectors, and inline passive optics for excess attenuation before replacing the transceiver. by LINK-PP Technical Support
Yes, this transceiver is available with vendor-specific coding for Netgear platforms. Please share your exact switch model and firmware version with our team to confirm the required module coding and ensure full interoperability. by LINK-PP Technical Support
It may be suitable if the complete optical path stays within the transmitter and receiver limits. Calculate the insertion loss of the MUX/DEMUX and other passive components, then validate the link using actual optical power measurements. by LINK-PP Technical Support
No, you should not treat the wavelengths as interchangeable. C57 uses 1531.89nm, while C58 uses 1531.12nm. Match the transceiver to the required MUX/DEMUX channel and the remote-end optical design. by LINK-PP Technical Support
We checked the SFF-8472 diagnostic support during procurement. It is useful for monitoring, but the actual values and display options also depend on the host device and its management software.
We wanted to add a C58 wavelength to our existing DWDM fiber system. The LS-DW5810-80I gives our engineers a specific 1531.12nm channel to plan around. We will check the MUX/DEMUX grid and total insertion loss before ordering the remaining modules.
Thailand · Thai · THB
