10G-SFPP-ZRD-1531.12-I represents a 10GBASE-DWDM SFP+ optical transceiver tuned to 1531.12nm (ITU C58) with throughput capability up to 10.7Gbps, qualified across an industrial case temperature range of -40°C to +85°C. The cooled EML laser and APD photodiode combination preserves signal fidelity over 80km SMF links, supported by real-time digital diagnostic monitoring (DDM) for ongoing performance visibility.
Brocade Part Number
10G-SFPP-ZRD-1531.12-I
Vendor Name
LINK-PP
Form Factor
SFP+
Max Data Rate
10.7Gbps
Wavelength
1531.12nm
Max Cable Distance
80km
Connector
Duplex LC
Media
SMF
Transmitter Type
EML
Receiver Type
APD
TX Power
-1 to +5dBm
RX Power
-23 to -6dBm
Receiver Sensitivity
-23dBm
DDM/DOM
Supported
Operating Temperature Range
-40 to +85°C
Protocols
10GBASE-ZR/ZW, SDH STM64, SFF-8431, SFF-8472
Key Features of Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP 10G SFP+
Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP brings 10G DWDM capacity to industrial fiber backbones with 80km reach and a ruggedized hardware build. Combining a 1531.12nm wavelength, duplex LC connectivity, and built-in diagnostics, it lets operators expand 10G capacity on existing single-mode routes while keeping links dependable in uncontrolled industrial environments.
This DWDM SFP+ transceiver follows the SFP+ Multi-Source Agreement, so it fits a wide range of switches and transport platforms without modification. Its hot-swappable design lets technicians replace or add units while the network stays online.
10G-SFPP-ZRD-1531.12-I: 10 Gbps Connectivity for Industrial Fiber Backbones
Line rates of up to 10.7Gbps let this DWDM module move large traffic volumes with very low latency. That steady 10G capacity suits industrial fiber backbones, where long-term headroom matters more than raw port count.
10G-SFPP-ZRD-1531.12-I Module with DWDM Technology for Fiber Efficiency
Dense wavelength division multiplexing lets several 10G DWDM channels travel over one fiber pair at the same time. Adding capacity this way avoids the cost and delay of pulling new cable through a plant.
10G-SFPP-ZRD-1531.12-I Module with 1531.12nm Wavelength
The transmitter inside this optical transceiver is locked to 1531.12nm, the ITU C58 channel on a 100GHz spacing plan. Holding that exact frequency keeps neighboring channels cleanly separated during multiplexing.
A sensitive APD receiver allows the module to carry signals up to 80km of single-mode fiber without regeneration. That reach removes the need for powered repeater sites along the route.
10G-SFPP-ZRD-1531.12-I Module with Duplex LC Interface
Standard duplex LC ports accept common single-mode patch cords and keep insertion loss low at every mating. The compact connector body also leaves room for tidy cabling in crowded racks.
10G-SFPP-ZRD-1531.12-I Module with DDM for Real-Time Monitoring
Digital diagnostic monitoring (DDM) reports transmit power, receive power, bias current, supply voltage, and operating temperature directly from the module. Engineers can read those values remotely to spot a degrading link before traffic drops.
The Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP 10G SFP+ DWDM transceiver is built and verified against recognized international standards, holding ISO 9001 for quality management alongside CE, RoHS, and FCC compliance so that it can be shipped and deployed in markets worldwide.
Before any DWDM module leaves the line, it passes a structured sequence of optical and electrical checks-spectral verification, eye diagram review, and bit error rate runs-that confirms each module behaves as specified under real traffic.
10G-SFPP-ZRD-1531.12-I Quality Certifications
The module's international approvals show that it was built to recognized manufacturing and environmental requirements, which gives network operators a documented basis for trusting its long-term reliability.
This product is in conformity with ISO9001. This system is valid to a company engaging in development, production and supply service of fiber optical products. Please contact us to learn more.
ISO/IEC 27001 is an international standard for managing and processing information security. This standard is jointly developed by the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). It sets out requirements for establishing, implementing, maintaining, and continually improving an information security management system (ISMS). Ensuring the confidentiality, integrity, and availability of organizational information assets, obtaining an ISO 27001 certificate means that the enterprise has passed the audit conducted by a certification body, proving that its information security management system has met the requirements of the international standard. Please contact us to learn more.
This product is in conformity with ISO14001.It is intended for use by an organization seeking to manage its environmental responsibilities in a systematic manner that contributes to the environmental pillar of sustainability. Please contact us to learn more.
ISO 45001 is a global standard that sets out the requirements for an occupational health and safety management system (OH&SMS).
REACH is a European Union regulation concerning the Registration, Evaluation, Authorization and Restriction of Chemicals. It came into force on 1st June 2007 and replaced a number of European Directives and Regulations with a single system. The regulation aims to protect human health and environmental safety, maintain and improve the competitiveness of the EU chemical industry, and develop innovative capabilities for non-toxic and harmless compounds to prevent market fragmentation, increase the transparency of the use of chemicals, promote non-animal experiments, and pursue sustainable social development.Please contact us to learn more.
This product meets the applicable requirements of Directive (EU) 2015/863 of RoHS. It restricts the use of 10 hazardous materials in the manufacture of various types of electronic and electrical equipment: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers, and four different phthalates. Please contact us to learn more.
This product fully accords with the FCC, which aims to manage the radio wave and magnetic fields more reasonably. Please contact us to learn more.
CB is an international system operated by IECEE. This product is based on IEC standards for testing the safety performance of electrical products. Please contact us to learn more.
This product fully accords with UKCA (UK Conformity Assessed) certificate, which signifies that it meets all relevant quality standards as well as health and safety requirements. Please contact us to learn more.
UL certification is a non-mandatory certification in the United States,mainly testing and certification of product safety performance.Its ultimate purpose is to obtain products with a fairly safe level for the market,and to contribute to ensuring human health and property safety.Please contact us to learn more.
10G-SFPP-ZRD-1531.12-I Certified for Reliable Host-Device Compatibility
This SFP+ DWDM transceiver is pre-programmed to match the identification data that major switch and router platforms expect, so it initializes normally and keeps a stable link without compatibility warnings.
Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP DWDM SFP+ transceiver undergoes strict testing to ensure stable performance in industrial environments. Learn more about our testing process at the LINK-PP Test Support Center.
Optical Spectrum Test
Verify wavelength accuracy and spectral stability for reliable DWDM transmission.
Eye Pattern Test
Check signal clarity and quality for stable optical data transmission.
Bit Error Rate Test
Measure data accuracy to ensure reliable long-distance optical signal transmission.
Temperature Test
Verify stable module performance under industrial operating temperature conditions.
Product Shipping for Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP 10G SFP+
Every Brocade 10G-SFPP-ZRD-1531.12-I Compatible LINK-PP 10G DWDM SFP+ module is packed to protect both its optical ports and its internal electronics from handling and transit hazards. Orders are processed promptly and shipped through established international channels to reach customers reliably.
Anti-Static Protective Packaging
Wrap each module against electrostatic discharge with anti-static packaging.
Shock-Resistant Transport Protection
Cushion each carton against impact and vibration during transit.
Fast Order Processing and Dispatch
Handle confirmed orders promptly and release stock for immediate dispatch.
Global Logistics and International Delivery
Ship worldwide through established carriers with reliable, trackable delivery.
Deploy the 10G-SFPP-ZRD-1531.12-I DWDM SFP+ by inserting the module into switch slots and connecting LC fiber cables directly to a matching-wavelength DWDM Mux/Demux. It builds high-density, long-haul industrial fiber backbones capable of stable 10G data transport across harsh environments.
10G-SFPP-ZRD-1531.12-I Technical Support
LINK-PP offers end-to-end technical support, from pre-sales consultation to post-deployment assistance, ensuring smooth integration and reliable network performance.
Pre-Sales Technical Consultation
Professional guidance to help you select the optimal 10G-SFPP-ZRD-1531.12-I module for your network design and application needs.
Compatibility Verification Support
Validated compatibility with LINK-PP switches and other mainstream networking platforms for seamless deployment.
Deployment & Installation Assistance
Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.
Long-Term Technical Assurance
Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.
Yes, DDM/DOM provides real-time telemetry for received optical power (Rx power), Tx power, and module temperature directly via your switch CLI or NMS. If Rx power drops near the sensitivity threshold, inspect the fiber route, connectors, and inline passive optics for excess attenuation before replacing the transceiver. by LINK-PP Technical Support
Yes, this transceiver is available with vendor-specific coding for Netgear platforms. Please share your exact switch model and firmware version with our team to confirm the required module coding and ensure full interoperability. by LINK-PP Technical Support
It may be suitable if the complete optical path stays within the transmitter and receiver limits. Calculate the insertion loss of the MUX/DEMUX and other passive components, then validate the link using actual optical power measurements. by LINK-PP Technical Support
No, you should not treat the wavelengths as interchangeable. C57 uses 1531.89nm, while C58 uses 1531.12nm. Match the transceiver to the required MUX/DEMUX channel and the remote-end optical design. by LINK-PP Technical Support
We checked the SFF-8472 diagnostic support during procurement. It is useful for monitoring, but the actual values and display options also depend on the host device and its management software.
Please write comments with more than three
character.
499019
616964
P***d
Denmark
Verified Purchase
5.0
2025-11-13
We wanted to add a C58 wavelength to our existing DWDM fiber system. The LS-DW5810-80I gives our engineers a specific 1531.12nm channel to plan around. We will check the MUX/DEMUX grid and total insertion loss before ordering the remaining modules.
Please write comments with more than three
character.
499019
616966
C***s
Nepal
Verified Purchase
5.0
2025-09-27
We need long-distance 10G connectivity between a regional aggregation node and a central equipment room. The cooled EML transmitter and APD receiver suit our initial design, and the specified 1531.12nm wavelength matches our C58 channel assignment.
Singapore · English · SGD
